Project

# Title Team Members TA Documents Sponsor
9 Dieagnosis
Josh Hartman
Megan Zeng
The Minh Pham
Yushi Zhou design_document1.pdf
proposal2.pdf
# Automated Optical Wafer Inspection System

Team Members:

- Megan Zeng (meganlz2)
- Josh Hartman (joshh3)

# Problem

In ECE 444, wafers are inspected under a microscope after fabrication steps to make sure the process was completed correctly. Since a wafer can contain dozens of dies and hundreds of devices, it is not practical to inspect every device after every fabrication step. Instead, only a small number of locations are usually inspected, and the rest of the wafer is assumed to be similar.

This can make it difficult to determine why a device fails after fabrication. For example, a problem with photoresist removal, etching, or deposition may affect a region of the wafer without being noticed during manual inspection. If the problem is only discovered during electrical testing, it can be difficult to determine which fabrication step caused it.

An automated inspection system could scan a much larger portion of the wafer after each fabrication step and identify regions that differ from the expected surface condition. This would provide additional information about where a fabrication problem may have occurred without requiring manual inspection of the entire wafer.

# Solution

We propose an automated optical wafer inspection system that uses a laser and photodiode to measure the optical response of different locations on a wafer. A low-power laser will illuminate the wafer, and a photodiode will measure reflected or scattered light from the surface. The measured signal will be compared against a baseline from an "ideal" wafer. Differences in the measured signal can indicate changes in the surface caused by fabrication anomalies.

The wafer will be mounted on an X-Y stage that moves it through a grid of measurement locations. The laser and photodiode will remain fixed while the wafer moves underneath them. A microcontroller will control the stage, collect measurements from the photodiode, and record the measurement location. The measurements will then be sent to a computer, where they will be compared against the baseline and displayed on a map of the wafer.

The system will be enclosed to reduce the effects of ambient light and keep the optical components in fixed positions. One intended application is inspecting a wafer after photoresist removal to identify regions where resist may remain before the wafer proceeds to a thermal processing step. Removing PR before a furnace step is important because PR can both severely contaminate the furnace and ruin sections of the wafer. Other surface anomalies may also be detectable depending on the optical response of the wafer at different stages of fabrication.

# Solution Components

## Subsystem 1: Optical Sensing

The optical sensing subsystem will illuminate the wafer and measure the reflected or scattered light. A low-power laser will be used so that the system can provide a consistent optical measurement at a small, localized point. Lenses may be used to control the size and focus of the laser spot on the wafer, depending on the results of initial testing.

The subsystem will contain:

- Laser: 650nm 5mW laser, specific part will be chosen based on cost and availability
- Photodiode: Vishay BPW34
- Transimpedance amplifier: Texas Instruments OPA380
- Filtering: RC low-pass filter
- Optical components: Lens and mounts for the laser and photodiode

The photodiode will produce a current based on the amount of incident light. The transimpedance amplifier will convert this current into a voltage that can be measured by the microcontroller. Filtering will be used to reduce noise in the measurement.

The exact optical geometry and lens configuration will be selected during development based on the measured signal strength and repeatability.

## Subsystem 2: Wafer Motion and Positioning

The motion subsystem will move the wafer through a predefined scan pattern and allow each optical measurement to be associated with a location on the wafer.

The subsystem will contain:

- Stepper motors: NEMA 17 stepper motors
- Motor drivers: Texas Instruments DRV8825
- Position sensors: Mechanical limit switches
- Stage: Custom X-Y motorized stage
- Wafer holder: Custom holder for a 4-inch wafer

The stage will be brought to a known origin using the limit switches before a scan begins. The microcontroller will then move the wafer to each measurement location based on the number of commanded motor steps. The system will pause briefly after each movement before taking a measurement so that vibrations from the motor do not significantly affect the optical measurement.

## Subsystem 3: Data Acquisition and Control

The data acquisition and control subsystem will control the scan, collect the photodiode measurements, and communicate with the computer.

The subsystem will contain:

- Microcontroller: STM32G474RET3
- ADC: Integrated in the MCU
- Motor control: Digital step/direction outputs for the DRV8825 drivers
- Limit switch inputs: Inputs for bringing stage to origin
- Communication: USB or UART connection to a host computer
- Custom PCB: Contains the microcontroller, optical sensing circuitry, motor interfaces, and power regulation

The microcontroller will control the motors and take one or more photodiode measurements at each scan location. Each measurement will be stored along with the corresponding X-Y position and then transmitted to the host computer.

## Subsystem 4: Data Processing and Wafer Mapping

The data processing subsystem will process the collected measurements and produce a map of the wafer.

The subsystem will contain:

- Host computer
- Python data processing software
- Python-based wafer mapping and visualization

A baseline scan will be used to determine the expected optical response for an ideal wafer condition. Measurements with a significant difference from the baseline will be marked as anomalies. The software will associate these measurements with their positions on the wafer and display the results as a two-dimensional map.

## Subsystem 5: Enclosure

The subsystem will hold the wafer, stage, laser, and photodiode in fixed positions while limiting ambient light reaching the photodiode.

The subsystem will contain:

- Enclosure: Custom machined housing
- Mounts: Mounts for the laser and photodiode. Possibly integrated into the enclosure

The enclosure will provide an environment for optical measurements and reduce noise caused by ambient lighting.

# Criterion For Success

1. Wafer positioning: The system will automatically move a 4-inch wafer through a predefined scan grid and return to a known home position.

2. Measurement repeatability: Consecutive measurements taken at the same wafer location under identical conditions will not have large swings (within 10% of each other).

3. Optical anomaly detection: The system will distinguish between two wafer surface conditions with a measurable difference in optical response.

4. Spatial mapping: The system will record the X-Y location of every optical measurement and generate a two-dimensional map covering the scanned region of the wafer.

5. Ambient-light rejection: With the enclosure installed, changes in ambient lighting will cause insignificant change (less than 5%) in the photodiode measurement.

Mobile Hive Checker

Rawda Abdeltawab, Fiona Cashin, Olivia Guido

Featured Project

# Team Members:

- Fiona Cashin (fcashin2)

- Olivia Guido (ojguido2)

- Rawda Abdeltawab (rawdaka2)

# Problem

Beekeepers must routinely monitor hive conditions to maintain healthy colonies. However, manually opening a hive significantly stresses the bees and disrupts their environment, and frequent disturbances can negatively affect bee behavior and productivity. On the other hand, insufficient monitoring can lead to swarming or freezing, resulting in the loss of an entire colony. Each lost colony can cost a beekeeper between $100 and $200. This highlights the need for a non-invasive solution for assessing the health of multiple hives, while minimizing stress on the bees. Although monitoring systems are available, they typically cost around $100 per hive, and many of the leading companies in this space are headquartered in Europe.

# Solution

The proposed solution is a portable device that enables beekeepers to monitor a colony’s health without opening the hive. A small sensor probe is inserted into the hive entrance to collect internal environmental data while the main unit remains outside. The device displays active sensor readings on an integrated screen and indicates whether hive conditions fall within acceptable ranges, such as temperatures between 70 and 97 degrees Fahrenheit. This approach minimizes hive disturbance while still providing essential health data including temperature, humidity, and carbon dioxide levels.

# Solution Components

## Subsystem 1, Temperature and Humidity Monitoring

This subsystem measures the internal temperature and humidity of the beehive.

Maintaining proper temperature is critical for hive health, as bee eggs will not develop and adult bees may die if the internal temperature falls outside the range between 70 and 97 degrees Fahrenheit. Humidity levels must remain between 50 percent and 60 percent to allow nectar to dry into honey. Excess humidity can promote pest reproduction, while insufficient humidity can cause bee eggs to dehydrate.

The device will use a temperature and humidity sensor connected via a long cable, allowing the sensor to be inserted into the hive while the user holds the device externally. The sensor will interface with a microcontroller unit (MCU), which will process the data and display the readings on an LCD screen. The MCU will evaluate whether the temperature and humidity values fall within the acceptable ranges. If the readings are normal, the display will show “PASSED.” If any reading is outside the normal range, the display will show “FAILED.”

Components:

- Digital Temperature Humidity Sensor : HiLetgo DHT21

- Microcontroller Unit (MCU) : ESP32-C3-WROOM-02

- Liquid Crystal Display (LCD) : B0DN9NMBFW (GODIYMODULES) or B0BWTFN9WF (Hosyond)

## Subsystem 2, Carbon Dioxide Monitoring

This subsystem measures the carbon dioxide concentration within the hive.

In a beehive, CO2 levels can be tolerated to a level of 8 percent, with higher levels indicating overcrowding and poor ventilation. The device will include a CO2 sensor connected via cable to the same MCU. The MCU will record the CO2 levels and display the results on the LED. As with the temperature and humidity subsystem, the MCU will determine whether the CO2 level is within the acceptable range and display “PASSED” or “FAILED” accordingly.

Components:

- CO2 Sensor : HiLetgo MHZ19

- Microcontroller Unit (MCU) : ESP32-C3-WROOM-02

- Liquid Crystal Display (LCD) : B0DN9NMBFW (GODIYMODULES) or B0BWTFN9WF (Hosyond)

## Subsystem 3, Microcontroller and Logic

The microcontroller coordinates all the subsystems and implements a Finite State Machine (FSM).

The MCU runs embedded C firmware that defines an FSM with at least four states, including “Start”, “Reset”, “Testing”, and “Done”. During the “Testing” state, sensor data is acquired via the appropriate communication protocols. Once testing is complete, the collected data is displayed on the LCD, allowing the user to assess the overall health of the hive. The MCU compares the data with the specified range to determine if the data is within range. This will prompt either a passed or failed responses to be displayed on the device

Components:

-Microcontroller Unit (MCU) : ESP32- option could be Espressif ESP32-C3-WROOM-02 which has RISC-V 32 bit CPU, antenna built-in, bluetooth, WIFI

-Programming Interface: use USB to upload code. USB can either charge battery/upload code, Arduino IDE platform

-Rest Button: PTS645SL43-2 LFS, resting the data on LCD to test another hive

-Power ON Button: PTS645SL43-2 LFS

-Liquid Crystal Display (LCD): B0DN9NMBFW (GODIYMODULES) or B0BWTFN9WF (Hosyond)

# Criterion For Success

- The humidity sensor accurately measures humidity.

- The temperature sensor accurately measures temperature.

- The display correctly shows the measured temperature.

- The display correctly shows the measured humidity.

- The display turns on when the ON button is pressed.

- A Start screen is shown when the ON button is pressed.

- A Testing screen is shown after the Start screen.

- A Done screen is displayed when the ON button is pressed the second time.

- A Reset Screen is displayed when the reset button is pressed.

- The display correctly shows “PASSED” and “FAILED.”

- The display shows “PASSED” when all sensor readings are within normal ranges.

- The display shows “FAILED” when at least one sensor reading is outside the normal range.

- Final product tested on multiple hives.

Project Videos