Project

# Title Team Members TA Documents Sponsor
3 Monitor for Dough and Sourdough Starter
Honorable Mention
 Abhitya Krishnaraj
Alec Thompson
Jake Hayes
 Tianxiang Zheng design_document2.pdf
final_paper1.pdf
photo1.png
photo2.jpg
presentation1.pptx
proposal2.pdf
video
Team Members:
- Jake Hayes (jhayes)
- Abhitya Krishnaraj (abhitya2)
- Alec Thompson (alect3)

# Problem

Making bread at home, especially sourdough, has become very popular because it is an affordable way to get fresh-baked bread that's free of preservatives and other ingredients that many people are not comfortable with. Sourdough also has other health benefits such as a lower glycemic index and greater bioavailability of nutrients.

However, the bulk fermentation process (letting the dough rise) can be tricky and requires a lot of attention, which leads to many people giving up on making sourdough. Ideally, the dough should be kept at around 80 degrees F, which is warmer than most people keep their homes, so many people try to find a warm place in their home such as in an oven with a light on; but it's hard to know if the dough is kept at a good temperature. Other steps need to be taken when the dough has risen enough, but rise time varies greatly, so you can't just set a timer; and if you wait too long the dough can start to shrink again. In the case of activating dehydrated sourdough starter, this rise and fall is normal and must happen several times; and its peak volume is what tells you when it's ready to use.

# Solution

Our solution is to design a device with a distance sensor (probably ultrasonic) and a temperature sensor that can be attached to the underside of most types of lids, probably with magnets. The sensors would be controlled with a microcontroller; and a display (probably LCD) would show the minimum, current, and maximum heights of the dough along with the temperature. This way the user can see at a glance how much the dough has risen, whether it has already peaked and started to shrink, and whether the temperature is acceptable or not. There is no need to remove it from its warm place and uncover it, introducing cold air; and there is no need to puncture it to measure its height or use some other awkward method.

The device would require a PCB, microcontroller, sensors, display, and maybe some type of wireless communication. Other features could be added, such as an audible alarm or a graph of dough height and/or temperature over time.

# Solution Components

## Height and Temperature Sensors

Sensors would be placed on the part of the device that attaches to the underside of a lid. A temperature sensor would measure the ambient temperature near the dough to ensure the dough is kept at an acceptable temperature. A proximity sensor or sensors would first measure the height of the container, then begin measuring the height of the dough periodically. If we can achieve acceptable accuracy with one distance sensor, that would be ideal; otherwise we could use 2-4 sensors.

Possible temperature sensor: [Texas Instruments LM61BIZ/LFT3](https://www.digikey.com/en/products/detail/texas-instruments/LM61BIZ%252FLFT3/12324753)

Proximity sensors could be ultrasonic, infrared LED, or VCSEL.\
Ultrasonic: [Adafruit ULTRASONIC SENSOR SONAR DISTANCE 3942](https://www.digikey.com/en/products/detail/adafruit-industries-llc/3942/9658069)\
IR LED: [Vishay VCNL3020-GS18](https://www.mouser.com/ProductDetail/Vishay-Semiconductors/VCNL3020-GS18?qs=5csRq1wdUj612SFHAvx1XQ%3D%3D)\
VCSEL: [Vishay VCNL36826S](https://www.mouser.com/ProductDetail/Vishay-Semiconductors/VCNL36826S?qs=d0WKAl%252BL4KbhexPI0ncp8A%3D%3D)

## MCU

An MCU reads data from the sensors and displays it in an easily understandable format on the LCD display. It also reads input from the user interface and adjusts the operation and/or output accordingly. For example, when the user presses the button to reset the minimum dough height, the MCU sends a signal to the proximity sensor to measure the distance, then the MCU reads the data, calculates the height, and makes the display show it as the minimum height.

Possible MCU: [STM32F303K8T6TR](https://www.mouser.com/ProductDetail/STMicroelectronics/STM32F303K8T6TR?qs=sPbYRqrBIVk%252Bs3Q4t9a02w%3D%3D)

## Digital Display
- A [4x16 Character LCD](https://newhavendisplay.com/4x16-character-lcd-stn-blue-display-with-white-side-backlight/) would attach to the top of the lid and display the lowest height, current height, maximum height, and temperature.

## User Interface

The UI would attach to the top of the lid and consist of a number of simple switches and push buttons to control the device. For example, a switch to turn the device on and off, a button to measure the height of the container, a button to reset the minimum dough height, etc.

Possible switch: [E-Switch RA1113112R](https://www.digikey.com/en/products/detail/e-switch/RA1113112R/3778055)\
Possible button: [CUI Devices TS02-66-50-BK-160-LCR-D](https://www.digikey.com/en/products/detail/cui-devices/TS02-66-50-BK-160-LCR-D/15634352)

## Power
- Rechargeable Lithium Ion battery capable of staying on for a few rounds of dough ([2000 mAh](https://www.microcenter.com/product/503621/Lithium_Ion_Battery_-_37v_2000mAh) or more) along with a USB charging port and the necessary circuitry to charge the battery. The two halves of the device (top and underside of lid) would probably be wired together to share power and send and receive data.

## (stretch goal) Wireless Notification System
- Push notifications to a user’s phone whenever the dough has peaked. This would likely be an add-on achieved with a Raspberry Pi Zero, Gotify, and Tailscale.

# Criterion For Success

- Charge the battery and operate on battery power for at least 10 hours, but ideally a few days for wider use cases and convenience.
- Accurately read (within a centimeter) and store distance values, convert distance to dough height, and display the minimum, maximum, and current height values on a display.
- Accurately read and report the temperature to the display.
- (stretch goal) Inform the user when the dough has peaked (visual, audio, or app based).

Active Cell Balancing for Solar Vehicle Battery Pack

Tara D'Souza, John Han, Rohan Kamatar

Featured Project

# Problem

Illini Solar Car (ISC) utilizes lithium ion battery packs with 28 series modules of 15 parallel cells each. In order to ensure safe operation, each battery cell must remain in its safe voltage operating range (2.5 - 4.2 V). Currently, all modules charge and discharge simultaneously. If any single module reaches 4.2V while charging, or 2.5V while discharging, the car must stop charging or discharging, respectively. During normal use, it is natural for the modules to become unbalanced. As the pack grows more unbalanced, the capacity of the entire battery pack decreases as it can only charge and discharge to the range of the lowest capacity module. An actively balanced battery box would ensure that we utilize all possible charge during the race, up to 5% more charge based on previous calculations.

# Solution Overview

We will implement active balancing which will redistribute charge in order to fully utilize the capacity of every module. This system will be verified within a test battery box so that it can be incorporated into future solar vehicles.

Solution Components:

- Test Battery Box (Hardware): The test battery box provides an interface to test new battery management circuitry and active balancing.

- Battery Sensors (Hardware): The current battery sensors for ISC do not include hardware necessary for active balancing. The revised PCB will include the active balancing components proposed below while also including voltage and temperature sensing for each cell.

- Active Balancing Circuit (Hardware): The active balancing circuit includes a switching regulator IC, transformers, and the cell voltage monitors.

- BMS Test firmware (Software): The Battery Management System requires new firmware to control and test active balancing.

# Criterion for Success

- Charge can be redistributed from one module to another during discharge and charge, to be demonstrated by collected data of cell voltages over time.

- BMS can control balancing.

- The battery pack should always be kept within safe operating conditions.

- Test battery box provides a safe and usable platform for future tests.